Free HPE7-A08 – Hp HPE7-A08 Practice Test Question

Answer is in the explanation below.

Select an option, then click Submit answer.

• ○ Configure VSX shutdown on-split on SW-B.
• ○ Configure keepalive VLAN on upstream lag.
• ○ Configure VSX shutdown on-split on SW-A.
• ○ Configure keepalive using mgmt ports between SW-A and SW-B.

Select an option, then click Submit answer.

• ○ UBT
• ○ GRE
• ○ IPSec
• ○ VNBT

Select an option, then click Submit answer.

• ○ Debug destination syslog
• ○ HPE Aruba Networking Central
• ○ SNMP get
• ○ NAE

Select an option, then click Submit answer.

• ○ Top-down/Bottom-up
• ○ Replace configuration
• ○ Spot the difference
• ○ Divide and conquer

Select an option, then click Submit answer.

• ○ Disable MSTP guard
• ○ Disable BPDU filter.
• ○ Disable loop protect.
• ○ Disable BPDU guard.

Select an option, then click Submit answer.

• ○ ISLP utilized the keepalive L3 connectivity to synchronize switch configuration.
• ○ ISLP requires a Routed Only Port to be enabled for VSX.
• ○ ISLP periodically synchronizes protocol states, such as RPVST+.
• ○ ISLP periodically synchronizes protocol states, such as LACP.

Select an option, then click Submit answer.

• ○ Upload new image to the secondary boot-bank on both switches.
• ○ Use vsx update-software boot-bank secondary.
• ○ Use vsx update-software boot-bank primary.
• ○ Use issu update-software confirm.

Select an option, then click Submit answer.

• ○

  

• ○

  qos trust dscp, cos C. D.

  

  

Select an option, then click Submit answer.

• ○ Active Gateway
• ○ HSRP
• ○ VRRP
• ○ Active Forwarding

Select an option, then click Submit answer.

• ○ Enable dhcpv4-snooping globally and on interface VLAN 20
• ○ Enable dhcpv4-snooping trust 10.100.100.10 on VLAN 20
• ○ Enable dhcpv4-snooping authorized-server 10.100.100.10 on VLAN 20
• ○ Enable dhcpv4-snooping globally and on VLAN 20

Select an option, then click Submit answer.

• ○ 64813
• ○ 65218
• ○ 63477
• ○ 65535

Select an option, then click Submit answer.

• ○ Replace configuration
• ○ Top-down/Bottom up
• ○ Spot the difference
• ○ Divide and conquer

Select an option, then click Submit answer.

• ○ The remote switch does not support BFD.
• ○ BFD is not supported on OSPF broadcast links, so OSPF ignores the config.
• ○ BFD has not been enabled at the global configuration level.
• ○ The local switch uses OSPFv3, but the remote switch uses OSPFv2.

Select an option, then click Submit answer.

• ○ The CX 6100 switches would need to be replaced with CX 6300 series.
• ○ The CX 6100 switches need to have the CX Advanced license applied to support the requirement.
• ○ The CX 6100 switches need to have a GRE tunnel to the HPE Aruba Networking 9240.
• ○ The CX 6100 switches need to have a static VXLAN tunnel to the HPE Aruba Networking CX 8325.