Loading demo links...
Showing 1–15 of 15 questions
DRAG DROP
Drag and drop the components from the left onto the descriptions on the right that indicate what occurs to Fibre Channel fabric when that component fails.
Select and Place:
Answer is in the explanation below.
An engineer must design a secondary site to prevent a catastrophic primary site failure. The applications must communicate across sites via the data link layer of the OSI model. The Layer 3 transport that is available for this solution consists of 10-Gb connections over Layer 3.
Which two solutions meet these requirements? (Choose two.)
Select all that apply, then click Submit answer.
OTV
vPC
OSPF
IS-IS
VXLAN EVPN
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by the delay of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations.
Which two features must be used to prevent these situations from happening in the future? (Choose two.)
Select all that apply, then click Submit answer.
peer-gateway
ip arp synchronize
delay restore
auto-recovery
system priority
A cloud service provider provisioned four active/active data centers in various locations within the country at 50 miles between each data center. The data centers must provide redundant network infrastructure and always be available to customers.
Which two data center design steps must be used to meet these requirements? (Choose two.)
Select all that apply, then click Submit answer.
Provide application hosting services to customers from the closest data center.
Implement active cluster in data centers 1 and 2 and backup in 3 and 4.
Use asynchronous replication between data centers 1 and 2.
Deploy database services in data center 1 and application layer to other data centers.
Configure application data replication to all backup data centers.
Which two statements describe Ethernet switching mode on Cisco UCS 6100 Series Fabric Interconnects? (Choose two.)
Select all that apply, then click Submit answer.
STP runs on the uplink ports of each VLAN, as defined by PVSTP+.
STP runs on the uplink ports of each VLAN, as defined by MSTP.
The STP parameter configuration is unsupported.
The STP parameter configuration is supported.
STP runs on the server ports.
A network engineer must design a Cisco HyperFlex solution based on these requirements:
• two clusters in the main data center consisting of five HyperFlex nodes
• one edge node for the remote branch
• cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
Select all that apply, then click Submit answer.
UCS B200
Gigabit Ethernet Switch
Fabric Interconnect 6300
HX240c
HX220c
What are two advantages of using Cisco vPC over traditional access layer designs? (Choose two.)
Select all that apply, then click Submit answer.
supports Layer 3 port channels
disables spanning-tree
no spanning-tree blocked ports
uses all available uplink bandwidth
maintains a single control plane
What are two characteristics of VRF-Lite on the Cisco NX-OS platform? (Choose two.)
Select all that apply, then click Submit answer.
Layer 3 interfaces can belong to multiple VRFs.
VRF-Lite interfaces can be Layer 2.
Overlapping IP addresses are permitted on different VRFs.
Interfaces that belong to VRFs can be physical or logical.
VRF-Lite interfaces support MPLS.
An engineer deploys VMware ESXi hypervisor on blade servers. The virtual networking is managed by Cisco Nexus 1000V Series Switches.
Which configuration aligns with Cisco recommended practices for providing high availability and a maximum throughput to the VMware ESXi hosts?
Select an option, then click Submit answer.
dual vNICs with static EtherChannel link aggregation
dual vNICs with hardware fabric failover on the fabric interconnects
dual vNICs with MAC pinning link aggregation
dual vNICs with LACP link aggregation
An engineer must connect an existing Cisco UCS Fabric Interconnect to an IP-based storage array. The connection must be a port channel made directly between the fabric interconnect expansion module and the storage array. The engineer must also consider that the environment is running FCoE for storage and uses QoS to prioritize traffic.
Which port type should be used to meet these requirements?
Select an option, then click Submit answer.
network
uplink
server
appliance
What is a design consideration when implementing FSPF?
Select an option, then click Submit answer.
Routes are based on the domain ID.
Routes are based on the distance vector protocol.
FSPF runs only on F Ports.
FSPF runs on a per-chassis basis.
Refer to the exhibit.
A Cisco UCS chassis that has two IOMs is discovered. The chassis discovery policy creates a fabric port channel.
What is the result of this policy?
Select an option, then click Submit answer.
Cisco UCS Manager creates two separate fabric port channels.
Cisco UCS Manager creates a single fabric port channel.
The port channel is disabled until an administrator enables it manually.
Each uplink that connects an IOM is configured as a discrete link.
An engineer must integrate Layer 4 to Layer 7 services within Cisco ACI Fabric. The main requirement is to have a single point of configuration for network elements and firewall policies.
Which action meets these requirements?
Select an option, then click Submit answer.
Define the service graph model as network policy mode.
Deploy the firewalls in routed mode with PBR.
Deploy the firewalls in transparent mode.
Define the service graph model as service policy mode.
An engineer enables the HSRP feature on a Cisco Nexus 7000 Series Switch. It must be ensured that the switch manages packets that are sent to the local vPC MAC address, remote vPC MAC address, and HSRP virtual MAC address.
Which command accomplishes this goal?
Select an option, then click Submit answer.
peer-switch
peer-gateway
map-server
hsrp preempt
Refer to the exhibit.
The security team created a new security policy that requires certain types of traffic to be subject to deep packet inspection The traffic types are
• internet traffic to application servers
• internet traffic to corporate users
• partner network traffic to application servers
• partner network traffic to corporate users
Where must the next-generation firewalls be inserted to implement the new policy?
Select an option, then click Submit answer.
one-armed insertion from the core switch cluster
inline insertion between the edge router duster and the core switch duster
one-armed insertion from the ACl border leaf cluster
inline insertion between the user network switch cluster and the core cluster
This page holds a free practice test for the Designing Cisco Data Center Infrastructure (DCID) (300-610) certification from Cisco. You will find 15 free questions, drawn from the full Study4Pass practice set of 111 questions for this exam. The free sample includes 7 single-answer, 7 multiple-answer and 1 drag-and-drop questions — the same mix of formats you will meet in the full set. The questions follow the same topic balance as the real exam: Network Design, Compute Design and Automation Design. The Cisco 300-610 exam is a certification exam that tests a candidate's knowledge and skills related to implementing Cisco Data Center technologies.
The target audience for the Cisco 300-610 exam is network professionals who have at least one year of experience in implementing and managing Cisco Enterprise Network Core Technologies. The Prerequisite for the Cisco 300-610 Exam is that you must hold either a valid Cisco CCNP Enterprise or Cisco CCIE Enterprise Infrastructure certification.
Use the sample the way you would use the real thing: answer each question on your own first, then open the explanation and make sure you understand why the right answer is right. That habit — reasoning instead of memorizing — is what carries over to exam day. When a topic keeps tripping you up, that is your study plan telling you where to go next.
When you finish the sample, do not just count the score — read it. Every missed question names a topic, and the full set lets you train that topic on its own until it stops costing you marks. That loop of test, review and targeted practice is how this set is designed to be used, from the first free question to the last simulation.
Inside the full 300-610 practice set:
Pick an answer for each question and check it straight away — the correct answer and a full explanation appear under the question. There is no time limit and nothing to sign up for. When an explanation is not enough, use Ask AI: this is an AI-Enabled practice test, and Ask AI explains the concept behind the question in plain language. Ready for more? The full 111-question set adds a timed Exam Simulation mode, topic training for your weak areas, and a flagged-question review, so you can practise the way the real exam feels.
Yes — the 15 questions on this page are completely free, with no signup and no payment details needed.
111 questions. The 15 free questions above are a sample of that full set, in the same style and topic balance.
Yes — every question shows the correct answer with an explanation, and Ask AI can explain the concept behind a question in plain words if you want to go deeper.
No. This is a practice test: the questions are written to mirror the real 300-610 exam’s topics and difficulty, not copied from it.
