Loading demo links...
Showing 1–15 of 15 questions
Drag and drop the features about multicast from the left onto the multicast protocols on the right. Not all options ate used.
Answer is in the explanation below.
See the solution below in Explanation.
Explanation:
Solution :-
R1
Router bgp 100
Neigh 10.3.3.3 remote-as 100
Neigh 10.3.3.3 update-source loopback0
Address-family ipv4
Neigh 10.3.3.3 next-hop-self
Aggregate-address 172.16.100.0 255.255.252.0 summary-only
Copy run start
R3
Router bgp 100
Neigh 10.1.1.1 remote-as 100
Neigh 10.1.1.1 update-source loopback 0
Copy run start
Verification:-
Answer is in the explanation below.
Refer to the exhibit. Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
Select all that apply, then click Submit answer.
The two routers are in the same area
The two routers are in different subnets
The two routers have password mismatch issues
The two routers have the same network ID
The two routers are in different areas
What are two differences between OSPF and IS-IS? (Choose two.)
Select all that apply, then click Submit answer.
Unlike IS-IS routers, an OSPF router belongs to only one area in addition to the backbone area
OSPF uses a router ID to identify a router, and IS-IS uses a system ID
OSPF is a link-state routing protocol, and IS-IS is a distance-vector routing protocol
Unlike OSPF, IS-IS supports virtual links
OSPF elects a DR and BDR, and IS-IS elects a DIS
While configuring Cisco NSF awareness, a network engineer enters the bgp graceful-restart command after the BGP session is established in a router that runs IOS XE Software. Graceful restart capabilities are not exchanged. Which two actions should be taken? (Choose two.)
Select all that apply, then click Submit answer.
Reload the router
Verity that BGP route dampening is configured
Reduce BGP convergence time
Issue the clear ip bgp * command
Issue the show ip bgp neighbors command.
What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)
Select all that apply, then click Submit answer.
A dynamic IPv6 address must be configured
A dynamic IPv4 address must be configured
A static IPv4 address must be configured
A static IPv6 address must be configured
Each tunnel endpoint must support IPv4 and IPv6
Cisco Express Forwarding must be enabled
Refer to the exhibit. Which two commands must the engineer configure for the company’s PIM-SM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface, without affecting normal operation? (Choose two.)
Select all that apply, then click Submit answer.
enable auto-rp listener
enable sparse-mode
enable Auto-RP announcements
enable sparse-dense mode
enable dense mode
Which two conditions must be met before separate ISPs can provide interdomain multicast routing? (Choose two.)
Select all that apply, then click Submit answer.
Each ISP must configure MSDP to connect its individual multicast administrative domain to the domains at other ISPs.
Each ISP must dedicate a single router to handle multicast traffic between providers.
Each ISP must replace its RP assignment with a global RP.
Each ISP must configure its network to use PIM-DM.
Each ISP must support intradomain multicast routing.
In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?
Select an option, then click Submit answer.
The receiver explicitly requests its desired traffic from the RP on the shared tree.
The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.
The RP on the shared tree floods traffic out of all PIM configured interfaces.
The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.
Refer to the exhibit.
After configuring IS-IS on routers R1 and R2, an engineer notices that only the loopback interface at 2000:1::1 /96 is known to router R2. Which change must be made so that only Loopback2 is advertised from R1 to R2?
Select an option, then click Submit answer.
Configure the router isis areal command under the LoopbackO interface on R1.
Remove the advertise passive-only command under the IS-IS address family ipv6 configuration
Remove the ipv6 router isis areal command under the Loopback2 interface on R1.
Remove the passive-interface Loopback0 command under the router isis areal configuration.
Refer to the exhibit.
Customer traffic from the branch site to the hub is experiencing packet drops. The engineer verified that:
Which action resolves the issue?
Select an option, then click Submit answer.
Redistribute the CE1 OSPF routes in the PE1 VRF.
Redistribute the CE2 OSPF routes in the PE2 VRF.
Advertise the VPNv4 routes of the branch site in CE2.
Advertise the VPNv4 routes of the hub in CE1.
Which keyword is used with the match route-type command to redistribute the external BGP and IGP routes using route map?
Select an option, then click Submit answer.
match route-type type-1
match route-type nssa-external
match route-type type-2
match route-type external
Refer to the exhibit.
The extension header of the IPv6 header is ignored when which value is equal to zero?
Select an option, then click Submit answer.
Segments Left
Hdr Ext Len
Routing Type
Next Header
Refer to the exhibit. A network engineer sets up a multihoming eBGP topology where multiple Autonomous Systems connect to ASN 64501. The engineer wants to block all the routes coming from ASN 64502 but allow all the others. For that purpose, the following AS Path prefix list is being used:
(config)#ip as-path access-list 10 deny _64502$
What must be fixed to achieve this result?
Select an option, then click Submit answer.
The AS-PATH filter must be defined inside the route-map mode
The statement must be modified with ip as-path access-list 1 deny_64502_
The statement must be modified with ip as-path access-list 1 deny ^64502$
At the end, ip as-path access-list 10 permit.* must be included
Refer to the exhibit. A network operator is troubleshooting TE tunnels and discovers that the soft preemption is not working as desired. Where should the soft preemption be applied to solve the issue?
Select an option, then click Submit answer.
under the tunnel-te1 interface on PE1
on the tail-end device for tunnel-te1 192.168.0.7
under the interface Loopback0 necessary for this deployment type
explicitly for tunnel-te 1 under the Cisco MPLS TE configuration mode after the timeout setting
Prepare for the Implementing Cisco Service Provider Advanced Routing Solutions (300-510) exam with this free practice test from Study4Pass, built around the real Cisco syllabus. The 15 questions come free from the full 203-question Study4Pass practice set — a quick, honest check of where you stand. The free sample includes 7 single-answer, 6 multiple-answer, 1 drag-and-drop and 1 hands-on lab questions — the same mix of formats you will meet in the full set. The set follows the real exam’s spread of topics: Unicast Routing, MPLS and Segment Routing, Routing Policy and Manipulation and Multicast Routing. The Cisco 300-510 exam is a professional-level exam that tests a candidate's knowledge and skills related to implementing and operating Cisco Service Provider Advanced Routing Solutions.
The target audience for the Cisco 300-510 exam is network engineers, systems engineers, and network administrators who have experience working with Cisco products and technologies. The recommended prerequisites for the Cisco 300-510 exam include a strong foundation in designing and implementing Cisco networks, as well as experience configuring and troubleshooting devices in a local and…
Work through the questions one at a time and read every explanation, even for the ones you get right — the reasoning behind an answer is what the real exam tests. If one area keeps costing you marks, you have found exactly what to revise before exam day.
Think of the result as a map, not a verdict. The questions you miss point straight at the topics that need work, and the explanations tell you why the correct option wins. Candidates who loop through that cycle — practise, review the reasoning, re-test — walk into the real exam having already seen their weak spots and fixed them.
Inside the full 300-510 practice set:
There is no clock and no account needed. Answer each question, check the result, and read the explanation before moving on. For anything that still feels unclear, Ask AI is built into this AI-Enabled practice test — it explains the concept behind the question so the next one like it gets easier. When the free sample feels comfortable, the full set of 203 questions adds timed Exam Simulation, topic-by-topic training, and flagged-question review — the closest thing to exam day you can get before the real thing.
Yes. Every question on this page — all 15 of them — is free to use, and you never need to create an account to try them.
The full Study4Pass set for 300-510 has 203 practice questions. This page gives you 15 of them free so you can judge the quality and difficulty first.
Yes. Check any question to reveal the correct answer and its explanation, and use Ask AI whenever you want the underlying concept explained step by step.
No — these are practice questions built to match the 300-510 domains and difficulty level, so you can prepare for the real exam with confidence.
